manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-0407ffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 7)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d0407ffff or 0x806f010d0407ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

Appendix A. Integrated management module II (IMM2) error messages

537

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

F5 ARX-2500 Installation Manual preview
ARX-2500
Brand: F5 Pages: 2
F5 WANJet 400 Appliance Upgrade Instructions preview
WANJet 400 Appliance
Brand: F5 Pages: 11
Kathrein EXIP 4124 Quick Start Quide preview
EXIP 4124
Brand: Kathrein Pages: 16
NEC Express5800/R310e-E4 User Manual preview
Express5800/R310e-E4
Brand: NEC Pages: 86
ACTi ACD-2200 Quick Installation Manual preview
ACD-2200
Brand: ACTi Pages: 15
Supermicro SuperServer 5039MD18-H8TNR User Manual preview
SuperServer 5039MD18-H8TNR
Brand: Supermicro Pages: 134
Supero SuperServer 6041G User Manual preview
SuperServer 6041G
Brand: Supero Pages: 114
IBM HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006 Supplementary Manual preview
HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006
Brand: IBM Pages: 1
Intel SBXL52 - Server Compute Blade Hardware Maintenance Manual preview
SBXL52 - Server Compute Blade
Brand: Intel Pages: 126
Hologic Cenova User Manual preview
Cenova
Brand: Hologic Pages: 30
IBM 88643RU - System x3850 - 8864 Service Manual preview
88643RU - System x3850 - 8864
Brand: IBM Pages: 192
Advantech EKI-1526 User Manual preview
EKI-1526
Brand: Advantech Pages: 96
Buffalo TERASTATION HS-D1.0TGL/R5 Technical Specifications preview
TERASTATION HS-D1.0TGL/R5
Brand: Buffalo Pages: 2
Boundless ADDS 6700 User Manual preview
ADDS 6700
Brand: Boundless Pages: 33
NEC SIGMABLADE AD106a Datasheet preview
SIGMABLADE AD106a
Brand: NEC Pages: 2
NEC Series3800/S120R-2 Datasheet preview
Series3800/S120R-2
Brand: NEC Pages: 2
NEC Series3800/S120R-1 Datasheet preview
Series3800/S120R-1
Brand: NEC Pages: 3
NEC Series3800/S110R-1 Datasheet preview
Series3800/S110R-1
Brand: NEC Pages: 2

Brands by name

Popular brands

Load more brands