manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

SAS
signal
cable

Power
cable

Configuration
cable

Hard disk drive
backplane

Figure 86. New backplane installation

a.

Connect the following cables in the order listed:

• Configuration cable 1

• Mini-SAS signal cable 2

• Power cable 3

b.

Angle the new backplane and place the bottom edge into the slots for backplane 2 on the
chassis next to the optical drive.

c.

Rotate the backplane upright so that the bracket goes underneath the latch and tabs on the
chassis and is engaged into the slots on the backplane bracket.

Step 7.

Touch the static-protective package that contains the RAID adapter to any unpainted metal surface
on the server. Then, remove the RAID adapter from the package.

Step 8.

Remove the PCI riser-card assembly 1 (see “Removing a PCI riser-card assembly” on page 37).

Step 9.

Install the RAID adapter in the connector on the PCI riser card (see “Installing an adapter” on
page 59).

Attention:

Incomplete insertion might cause damage to the server or the adapter.

Step 10. Connect the mini-SAS signal cables to the connectors on the RAID adapter.

Step 11. Align and install the PCI riser-card assembly in the server (see “Installing a PCI riser-card

assembly” on page 137).

100

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

TANDBERG S3 Administrator'S Manual preview
S3
Brand: TANDBERG Pages: 127
360 Systems MAXX-2400-HD Specification preview
MAXX-2400-HD
Brand: 360 Systems Pages: 8
Sans Digital Mobileraid MR8X Detailed User'S Manual preview
Mobileraid MR8X
Brand: Sans Digital Pages: 81
Tangent Thin Client 166 Datasheet preview
Thin Client 166
Brand: Tangent Pages: 2
NEC N8100-2834F Maintenance Manual preview
N8100-2834F
Brand: NEC Pages: 138
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual preview
PRIMERGY CX400 M6
Brand: Fujitsu Pages: 209
Fujitsu PRIMERGY CX272 S1 Upgrade And Maintenance Manual preview
PRIMERGY CX272 S1
Brand: Fujitsu Pages: 234
Fujitsu Primergy CX270 S2 Upgrade And Maintenance Manual preview
Primergy CX270 S2
Brand: Fujitsu Pages: 320
Fujitsu Primergy CX270 S2 Operating Manual preview
Primergy CX270 S2
Brand: Fujitsu Pages: 56
Oracle SPARC T8 Series Licensing Information User Manual preview
SPARC T8 Series
Brand: Oracle Pages: 12
Digi 70002405 User Manual preview
70002405
Brand: Digi Pages: 163
HP AlphaServer ES47 Installation Manual preview
AlphaServer ES47
Brand: HP Pages: 76
HP AlphaServer GS80 Upgrade Manual preview
AlphaServer GS80
Brand: HP Pages: 88
HP 16-way Specification preview
16-way
Brand: HP Pages: 39
HP 16/18-Port Cable Management Kit Installation Manual preview
16/18-Port Cable Management Kit
Brand: HP Pages: 14
HP 11Q98EA#ABU User Manual preview
11Q98EA#ABU
Brand: HP Pages: 49
HP AlphaServer ES47 Cli Reference Manual preview
AlphaServer ES47
Brand: HP Pages: 152
HP AlphaStation DS20 Specifications preview
AlphaStation DS20
Brand: HP Pages: 15

Brands by name

Popular brands

Load more brands