manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Serviceable

No

Automatically notify support

No

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-885-002 : Standalone Memory Test Aborted

Processor does not support MTRR register manipulation. Can not write to memory without cache.

Recoverable

No

Severity

Warning

Serviceable

No

Automatically notify support

No

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-885-003 : Standalone Memory Test Aborted

Processor does not support MTRR register manipulation. Can not write to memory without cache.

Appendix C. DSA diagnostic test results

1145

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM 8832 Deployment Manual preview
8832
Brand: IBM Pages: 54
LaCie 301160U - 1TB Ethernet Disk RAID Network Attached... Quick Install Manual preview
301160U - 1TB Ethernet Disk RAID Network Attached...
Brand: LaCie Pages: 5
NEC Express5800/R120h-1E Manual preview
Express5800/R120h-1E
Brand: NEC Pages: 52
IBM DB2 9 Planning Manual preview
DB2 9
Brand: IBM Pages: 51
Integra NAS-2.3 Instruction Manual preview
NAS-2.3
Brand: Integra Pages: 40
IOGear GMFPSU01 User Manual preview
GMFPSU01
Brand: IOGear Pages: 44
IBM System X Series Rack Installation Instructions preview
System X Series
Brand: IBM Pages: 6
Navico SonicHub 2 Installation Manual preview
SonicHub 2
Brand: Navico Pages: 2
Motorola WPS870G - Wireless Print Server User Manual preview
WPS870G - Wireless Print Server
Brand: Motorola Pages: 115
PCI Mini-101M User Manual preview
Mini-101M
Brand: PCI Pages: 87
MSI MS-96E3 User Manual preview
MS-96E3
Brand: MSI Pages: 54
MSI MS-9249 User Manual preview
MS-9249
Brand: MSI Pages: 86
DNP WPS PRO User Manual preview
WPS PRO
Brand: DNP Pages: 136
Axis 850 User Manual preview
850
Brand: Axis Pages: 69
Polycom KIRK 500 User Manual preview
KIRK 500
Brand: Polycom Pages: 34
Transition Networks SDSTX3110-121S-LRT User Manual preview
SDSTX3110-121S-LRT
Brand: Transition Networks Pages: 109
Planet NAS-7102 User Manual preview
NAS-7102
Brand: Planet Pages: 68
BushkaBlue FF06-6P User Manual preview
FF06-6P
Brand: BushkaBlue Pages: 30

Brands by name

Popular brands

Load more brands