Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 449

Page: 449 / 1222

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0494

User Response

1. Reduce the ambient temperature.

2. Ensure the air baffle is installed correctly.

3. Check the server airflow. Make sure that nothing is blocking the air from coming into or

preventing the air from exiting the server.

•

80010901-1401ffff : Numeric sensor [NumericSensorElementName] going high (upper critical) has

asserted. (CPU1 VR Temp)

This message is for the use case when an implementation has detected an Upper Critical sensor going
high has asserted.

May also be shown as 800109011401ffff or 0x800109011401ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0494

User Response

1. Reduce the ambient temperature.

2. Ensure the air baffle is installed correctly.

Appendix A. Integrated management module II (IMM2) error messages

437

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands