Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 335

Page: 335 / 1222

Battery

Figure 231. System battery installation

Tilt the battery so that you can insert it into the socket on the side opposite the battery clip.

Figure 232. System battery installation

Press the battery down into the socket until it clicks into place. Make sure that the battery clip
holds the battery securely.

If you removed a rubber cover from the battery holder, use your fingers to install the battery
cover on top of the battery connector.

Step 7.

Reinstall the PCI riser-card assembly 2 (see “Replacing a PCI riser-card assembly” on page 278), if
necessary.

Step 8.

Install the cover (see “Replacing the cover” on page 240).

Step 9.

Slide the server into the rack.

Step 10. Reconnect the external cables; then, reconnect the power cords and turn on the peripheral devices

and the server.

Step 11. Start the Setup utility and reset the configuration.

Chapter 6

Removing and replacing components

323

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands