manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - other

SNMP Trap ID

22

CIM Information

Prefix:

IMM

ID:

0040

User Response

Information only; no action is required.

•

40000029-00000000 : Security: Userid: [arg1] had [arg2] login failures from an SSH client at IP

address [arg3].

This message is for the use case where a user has failed to log in to a Management Controller from SSH.

May also be shown as 4000002900000000 or 0x4000002900000000

Severity

Info

Serviceable

No

Automatically notify support

No

Alert Category

System - Remote Login

SNMP Trap ID

30

CIM Information

Prefix:

IMM

ID:

0041

User Response

Complete the following steps until the problem is solved:

1. Make sure that the correct login ID and password are being used.

2. Have the system administrator reset the login ID or password.

•

4000002a-00000000 : [arg1] firmware mismatch internal to system [arg2]. Please attempt to flash

the [arg3] firmware.

This message is for the use case where a specific type of firmware mismatch has been detected.

May also be shown as 4000002a00000000 or 0x4000002a00000000

Appendix A. Integrated management module II (IMM2) error messages

375

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM Eserver xSeries 360 Type 8686 Installation Manual preview
Eserver xSeries 360 Type 8686
Brand: IBM Pages: 74
Aaeon AIOT-ILRA01 User Manual preview
AIOT-ILRA01
Brand: Aaeon Pages: 38
IEI Technology PUZZLE-IN003A User Manual preview
PUZZLE-IN003A
Brand: IEI Technology Pages: 89
IBM System x3250 M3 Type 4251 Manual preview
System x3250 M3 Type 4251
Brand: IBM Pages: 32
Quanta Computer STRATOS S400-X44E Technical Manual preview
STRATOS S400-X44E
Brand: Quanta Computer Pages: 251
Acrosser Technology ANR-C62-N1 Series Manual preview
ANR-C62-N1 Series
Brand: Acrosser Technology Pages: 57
IBM totalstorage fastt100 Installation, User And Maintenance Manual preview
totalstorage fastt100
Brand: IBM Pages: 160
Zeiss 5034555 User Manual preview
5034555
Brand: Zeiss Pages: 12
Edimax Past Ethernet Combo Print Server PS-1216U Quick Installation Manual preview
Past Ethernet Combo Print Server PS-1216U
Brand: Edimax Pages: 23
Lenovo 7Y45 Setup Manual preview
7Y45
Brand: Lenovo Pages: 116
Lenovo 70F0 User Manual And Hardware Maintenance Manual preview
70F0
Brand: Lenovo Pages: 96
Lenovo 8753 Product Manual preview
8753
Brand: Lenovo Pages: 46
Lenovo 7Y54 Maintenance Manual preview
7Y54
Brand: Lenovo Pages: 138
Lenovo 8871 Product Manual preview
8871
Brand: Lenovo Pages: 56
Lenovo 8869 Product Manual preview
8869
Brand: Lenovo Pages: 64
Lenovo DU User Manual preview
DU
Brand: Lenovo Pages: 226
Lenovo BladeCenter HS22 Installation And User Manual preview
BladeCenter HS22
Brand: Lenovo Pages: 96
Lenovo BladeCenter HS23 Installation And User Manual preview
BladeCenter HS23
Brand: Lenovo Pages: 104

Brands by name

Popular brands

Load more brands