manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Severity

Error

User Response

Complete the following steps:

1. Verify that the Processor is a valid option that is listed as a Server Proven device for this system.

If not, remove the Processor and install a Server Proven one.

2. Verify that matching Processors are installed in the correct Processor sockets according to the

service information for this product. Correct any mismatch found.

3. Check IBM support site for an applicable service bulletin or firmware update that applies to

this processor error.

4. (Trained Service technician only) Replace the Processor. Inspect Processor socket and replace

the system board first if socket is damaged

•

I.1800B [I.1800B] A cache size mismatch has been detected for one or more processor packages.

Explanation:

Processors have one or more cache levels with mismatched size

Severity

Error

User Response

Complete the following steps:

1. Verify that matching processors are installed in the correct processor sockets according to the

service information for this product. Correct any mismatch found.

2. Check IBM support site for an applicable service bulletin or firmware update that applies to

this Processor error.

3. (Trained Service technician only) Replace the system board.

•

I.1800C [I.1800C] A cache type mismatch has been detected for one or more processor packages.

Explanation:

Processors have one or more cache levels with mismatched type

Severity

Error

User Response

Complete the following steps:

1. Verify that matching Processors are installed in the correct Processor sockets according to the

service information for this product.

2. Check IBM support site for an applicable service bulletin or firmware update that applies to

this Processor error.

3. (Trained Service technician only) Replace the system board.

•

I.1800D [I.1800D] A cache associativity mismatch has been detected for one or more processor

packages.

Explanation:

Processors have one or more cache levels with mismatched associativity

Severity

1010

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

NEC Univerge SV9100 System Maintenance Manual preview
Univerge SV9100
Brand: NEC Pages: 78
NEC UNIVERGE SL2100 Manual preview
UNIVERGE SL2100
Brand: NEC Pages: 34
NEC SV8500 Overview preview
SV8500
Brand: NEC Pages: 2
NEC SV8500 Operation And Maintenance Manual preview
SV8500
Brand: NEC Pages: 975
Lantronix SLC 8000 Demo Manual preview
SLC 8000
Brand: Lantronix Pages: 10
Lantronix xport pro Integration Manual preview
xport pro
Brand: Lantronix Pages: 17
Lantronix PremierWave XC User Manual preview
PremierWave XC
Brand: Lantronix Pages: 109
Lantronix XPort Integration Manual preview
XPort
Brand: Lantronix Pages: 24
Lantronix WiPort Integration Manual preview
WiPort
Brand: Lantronix Pages: 29
Lantronix XPress DR+ Quick Connect preview
XPress DR+
Brand: Lantronix Pages: 2
Sybase Adaptive Server IQ 12.4.2 Administration And Performance Manual preview
Adaptive Server IQ 12.4.2
Brand: Sybase Pages: 536
IBM 88723RU User Manual preview
88723RU
Brand: IBM Pages: 106
nvent SCHROFF 11850-016 User Manual preview
SCHROFF 11850-016
Brand: nvent Pages: 18
Gigabyte R283-S93-AAF1 User Manual preview
R283-S93-AAF1
Brand: Gigabyte Pages: 115
HPE ProLiant DL580 Gen10 User Manual preview
ProLiant DL580 Gen10
Brand: HPE Pages: 158
Supero SUPERSERVER 6015C-M3 User Manual preview
SUPERSERVER 6015C-M3
Brand: Supero Pages: 118
Dot Hill AssuredSAN 4004 Series Fru Installation And Replacement Manual preview
AssuredSAN 4004 Series
Brand: Dot Hill Pages: 59
Fibrenetix SVS Series Quick Installation Manual preview
SVS Series
Brand: Fibrenetix Pages: 17

Brands by name

Popular brands

Load more brands