manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

0

0

0

0

0

0

0

0000

0000

0000

0000

000

000

000

000

Thumbscrew

Pin

Figure 258. System board removal

Step 16. Remove the socket covers from the microprocessor sockets on the new system board and place

them on the microprocessor sockets of the old system board that you are removing.

Step 17. If you are instructed to return the system board, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Attention:

Make sure to place the socket covers for the microprocessor sockets on the system

board before returning the system board.

Replacing the system board

Use this information to replace the system board.

Notes:

1. When you reassemble the components in the server, be sure to route all cables carefully so that they are

not exposed to excessive pressure.

Chapter 6

.

Removing and replacing components

341

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Xerox EX Specification Sheet preview
EX
Brand: Xerox Pages: 2
Xerox EX Brochure & Specs preview
EX
Brand: Xerox Pages: 2
IBM Netfinity 5000 Setup And Installation Manual preview
Netfinity 5000
Brand: IBM Pages: 24
Fujitsu PRIMERGY Econel 230R S1 Service Supplement Manual preview
PRIMERGY Econel 230R S1
Brand: Fujitsu Pages: 53
Fujitsu Primergy ECONEL 100 S2 Start Manual preview
Primergy ECONEL 100 S2
Brand: Fujitsu Pages: 8
Fujitsu PRIMERGY Econel 200 S2 Options Manual preview
PRIMERGY Econel 200 S2
Brand: Fujitsu Pages: 65
Fujitsu PRIMERGY MX130 S1 Operating Manual preview
PRIMERGY MX130 S1
Brand: Fujitsu Pages: 85
Fujitsu PRIMERGY Econel 100 Operating Manual preview
PRIMERGY Econel 100
Brand: Fujitsu Pages: 64
Fujitsu primergy h250 Manual preview
primergy h250
Brand: Fujitsu Pages: 105
Fujitsu Primergy N800 Manual preview
Primergy N800
Brand: Fujitsu Pages: 142
Fujitsu PRIMERGY GX2460 M1 Upgrade And Maintenance Manual preview
PRIMERGY GX2460 M1
Brand: Fujitsu Pages: 251
Fujitsu PRIMERGY MX130 S2 Upgrade and maintenance manua Upgrade And Maintenance Manual preview
PRIMERGY MX130 S2 Upgrade and maintenance manua
Brand: Fujitsu Pages: 256
Fujitsu Primergy RX100 S2 User Manual preview
Primergy RX100 S2
Brand: Fujitsu Pages: 275
Fujitsu Primergy RX100 S3 User Manual preview
Primergy RX100 S3
Brand: Fujitsu Pages: 287
Fujitsu PRIMERGY ECONEL30 Configuration Manual preview
PRIMERGY ECONEL30
Brand: Fujitsu Pages: 11
CryptoTelecom S-160 User Manual preview
S-160
Brand: CryptoTelecom Pages: 86
Silicon Graphics CHALLENGE CMN A012B Owner'S Manual preview
CHALLENGE CMN A012B
Brand: Silicon Graphics Pages: 40
7th Sense VIOSO User Manual preview
VIOSO
Brand: 7th Sense Pages: 24

Brands by name

Popular brands

Load more brands