Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 474

Page: 474 / 1222

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0522

User Response

None

•

8007020d-2b81ffff : Sensor [SensorElementName] has transitioned to critical from a less severe

state. (FDIMM Endurance)

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

May also be shown as 8007020d2b81ffff or 0x8007020d2b81ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0522

User Response

None FDIMM Warranty :

•

8007020f-2201ffff : Sensor [SensorElementName] has transitioned to critical from a less severe

state. (TXT ACM Module)

This message is for the use case when an implementation has detected a Sensor transitioned to critical
from less severe.

May also be shown as 8007020f2201ffff or 0x8007020f2201ffff

462

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands