Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 40

Page: 40 / 1222

System-board internal connectors

The following illustration shows the internal connectors on the system board.

RAID upgrade
connector

Optical disk drive
connector

USB tape drive
connector

Operator information
panel connector

PCI riser
connector 1

10G Ethernet
connector

PCI riser
connector 2

Video card power
connector 1

USB hypervisor
connector

Power signal
connector
(2nd power supply
to system board)

Power supply
connector
(2nd power supply
to system board)

Microprocessor 2

Fan 4 connector

Fan 3
connector

Fan 2
connector

Fan 1
connector

Front video
connector

SAS/SATA backplane
config connector 1

Front USB
connector

Tape drive
power
connector

Microprocessor 1

DIMM connectors

NMI button

Battery

SAS 0

SAS 1

SAS/SATA backplane
power connector

SAS/SATA
backplane
config
connector 2

Video card power
connector 2

Figure 15. System-board internal connectors

System-board external connectors

The following illustration shows the external connectors on the system board.

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands