manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Serviceable

No

Automatically notify support

No

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-871-003 : Standalone Memory Test Aborted

Data Mis-compare encountered.

Recoverable

No

Severity

Warning

Serviceable

No

Automatically notify support

No

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

201-877-000 : Standalone Memory Test Aborted

BIOS: Sparing in Extended PCI reg. must be OFF. Go to setup and disable sparing.

Appendix C. DSA diagnostic test results

1139

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Supermicro SuperServer 6019P-WT User Manual preview
SuperServer 6019P-WT
Brand: Supermicro Pages: 133
IBM TotalStorageFAStT900 User Manual preview
TotalStorageFAStT900
Brand: IBM Pages: 112
ClearCube CD8620 series User Manual preview
CD8620 series
Brand: ClearCube Pages: 5
Promise Technology PegasusPro R16 Product Manual preview
PegasusPro R16
Brand: Promise Technology Pages: 80
Viavi G3-GS-8P-288T Hardware Installation preview
G3-GS-8P-288T
Brand: Viavi Pages: 8
Multitech ProxyServer MTPSR1-202ST User Manual preview
ProxyServer MTPSR1-202ST
Brand: Multitech Pages: 142
360 Systems MAXX-2420-EX Operation Manual preview
MAXX-2420-EX
Brand: 360 Systems Pages: 148
Inventec N800G3 User Manual preview
N800G3
Brand: Inventec Pages: 258
NASdeluxe NDL-2700T+ Installation Manual preview
NDL-2700T+
Brand: NASdeluxe Pages: 6
Planex Mini-103MN User Manual preview
Mini-103MN
Brand: Planex Pages: 70
Planex mini-mfp User Manual preview
mini-mfp
Brand: Planex Pages: 101
GIGA-BYTE TECHNOLOGY G492-Z50 User Manual preview
G492-Z50
Brand: GIGA-BYTE TECHNOLOGY Pages: 141
Planet NAS-7101 User Manual preview
NAS-7101
Brand: Planet Pages: 49
Dell EMC PowerEdge T140 Technical Manual preview
PowerEdge T140
Brand: Dell EMC Pages: 43
Aaeon FWS-2200 Manual preview
FWS-2200
Brand: Aaeon Pages: 108
IBM SAN512B-6 Installation, Service And User Manual preview
SAN512B-6
Brand: IBM Pages: 286
IBM x3200 M2 Type 4367 User Manual preview
x3200 M2 Type 4367
Brand: IBM Pages: 102
QNAP TS-32XU Series User Manual preview
TS-32XU Series
Brand: QNAP Pages: 55

Brands by name

Popular brands

Load more brands