Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 569 | Manualshive

Page: 569 / 1222

background image

If the specified sensor is front USB connector, reset the front USB cable on the system board. If
the specified sensor is front video connector, reset the front video cable in the system board. If the
specified sensor is PwrPaddle cable, complete the following steps until problem is solved:

1. Reseat the power paddle cable on the system board.

2. Replace the power paddle cable.

3. (Trained technician only) Replace the supercap n. (n = supercap number)

4. (Trained technician only) Replace the system board.

•

806f011b-2508ffff : The connector [PhysicalConnectorElementName] has encountered a

configuration error. (nvDIMM 08 Cable)

This message is for the use case when an implementation has detected an Interconnect Configuration
Error.

May also be shown as 806f011b2508ffff or 0x806f011b2508ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Other

SNMP Trap ID

50

CIM Information

Prefix:

PLAT

ID:

0266

User Response

If the specified sensor is front USB connector, reset the front USB cable on the system board. If
the specified sensor is front video connector, reset the front video cable in the system board. If the
specified sensor is PwrPaddle cable, complete the following steps until problem is solved:

1. Reseat the power paddle cable on the system board.

2. Replace the power paddle cable.

3. (Trained technician only) Replace the supercap n. (n = supercap number)

4. (Trained technician only) Replace the system board.

•

806f011b-250bffff : The connector [PhysicalConnectorElementName] has encountered a

configuration error. (nvDIMM 11 Cable)

This message is for the use case when an implementation has detected an Interconnect Configuration
Error.

May also be shown as 806f011b250bffff or 0x806f011b250bffff

Appendix A. Integrated management module II (IMM2) error messages

557

«
...
567
568
569
570
571
...
»

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Brand: Razberi Pages: 113

Brand: IBM Pages: 51

AssuredSAN 4004 Series

Brand: Dot Hill Pages: 59

Brand: Kontron Pages: 90

Proliant BL480c

Brand: HP Pages: 65

ProLiant BL420c

Brand: HP Pages: 88

Brand: HP Pages: 34

ProLiant BL685c G5

Brand: HP Pages: 23

ProLiant BL660c Gen 9

Brand: HP Pages: 3

ProLiant BL460c G7

Brand: HP Pages: 74

ProLiant BL495c G6

Brand: HP Pages: 90

ProLiant BL685c G7

Brand: HP Pages: 67

ProLiant BL280c Generation 6 (G6)

Brand: HP Pages: 36

ProLiant BL620c Generation 7

Brand: HP Pages: 42

ProLiant BL685c Generation 6

Brand: HP Pages: 33

ProLiant BL660c Gen9

Brand: HP Pages: 37

ProLiant DL120 G7

Brand: HP Pages: 105

ProLiant BL465c Generation 7 (G7)

Brand: HP Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands