manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Hard disk drive
backplate

SAS
signal
cable

Power
cable

Latch

Figure 225. 3.5-inch simple-swap/hot-swap hard disk drive backplate assembly/backplane removal

Step 7.

Disconnect the power and signal cables from the system board.

Step 8.

If you are instructed to return the hard disk drive backplate assembly/backplane, follow all
packaging instructions, and use any packaging materials for shipping that are supplied to you.

Replacing the 3.5-inch simple-swap/hot-swap hard disk drive backplate
assembly/backplane

Use this information to replace the 3.5-inch simple-swap/hot-swap hard disk drive backplate
assembly/backplane.

To install the 3.5-inch simple-swap/hot-swap hard disk drive backplate assembly/backplane, complete the
following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Align the sides of the drive backplate assembly/backplane with the slots on the bracket.

Step 3.

Lower the backplate assembly/backplane into the slots on the chassis.

Step 4.

Rotate the top of the backplate assembly/backplane until the front tab clicks into place into the
latches on the chassis.

316

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

TYAN FT83-B7119 Service Engineer'S Manual preview
FT83-B7119
Brand: TYAN Pages: 221
Xantech XMUSICWP User Manual preview
XMUSICWP
Brand: Xantech Pages: 52
IBM xSeries 200VL Installation Manual preview
xSeries 200VL
Brand: IBM Pages: 70
HP 2500 - Color LaserJet Laser Printer Installation Manual preview
2500 - Color LaserJet Laser Printer
Brand: HP Pages: 24
HP 2101nw User Manual preview
2101nw
Brand: HP Pages: 26
HP 4650 - Color LaserJet Laser Printer Install Manual preview
4650 - Color LaserJet Laser Printer
Brand: HP Pages: 2
HP 615N - JetDirect Print Server Setup Manual preview
615N - JetDirect Print Server
Brand: HP Pages: 56
HP 4550 - Color LaserJet Laser Printer Hardware Installation Manual preview
4550 - Color LaserJet Laser Printer
Brand: HP Pages: 32
HP 600N - JetDirect Print Server Hardware Installation Manual preview
600N - JetDirect Print Server
Brand: HP Pages: 44
HP 170X - JetDirect Print Server Hardware Installation Manual preview
170X - JetDirect Print Server
Brand: HP Pages: 30
HP 170X - JetDirect Print Server Installation And Configuration Manual preview
170X - JetDirect Print Server
Brand: HP Pages: 80
HP Appliance 4200 Manual preview
Appliance 4200
Brand: HP Pages: 116
HP 300X - JetDirect Print Server Administrator'S Manual preview
300X - JetDirect Print Server
Brand: HP Pages: 102
HP 635n Administrator'S Manual preview
635n
Brand: HP Pages: 194
HP 635n - JetDirect IPv6/IPsec Print Server Administrator'S Manual preview
635n - JetDirect IPv6/IPsec Print Server
Brand: HP Pages: 202
HP 4600 - Color LaserJet Laser Printer Technical Reference Manual preview
4600 - Color LaserJet Laser Printer
Brand: HP Pages: 309
HP Color laserjet 5500 Installation Manual preview
Color laserjet 5500
Brand: HP Pages: 6
MPI Technologies LAN Brick Eth 10 Specification Sheet preview
LAN Brick Eth 10
Brand: MPI Technologies Pages: 2

Brands by name

Popular brands

Load more brands