manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

• Tape drive power cable to the system board

Tape drive
power cables

SATA tape
drive signal
cable

Figure 118. Cable connections

Step 6.

Slide the tape-drive assembly most of the way into the tape-drive bay.

Step 7.

Connect the SAS signal cable and the power cable to the back of the tape drive.

Attention:

Make sure that all the cables are positioned underneath the tape-drive assembly before

you insert the assembly in the tape-drive bay. Otherwise, the cables might be damaged.

Step 8.

Slide the tape-drive assembly the rest of the way into the tape-drive bay.

Step 9.

Push the latch to the closed (locked) position.

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on
page 136.

Installing a USB embedded hypervisor flash device

Use this information to install a USB embedded hypervisor flash device.

To install a USB hypervisor flash device, complete the following steps:

126

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Datacom DM-SV01 Product Manual preview
DM-SV01
Brand: Datacom Pages: 89
Advantech EKI-152X series User Manual preview
EKI-152X series
Brand: Advantech Pages: 94
TYAN Transport GT26-B4987 Service Manual preview
Transport GT26-B4987
Brand: TYAN Pages: 125
Advantech PAC-4010 User Manual preview
PAC-4010
Brand: Advantech Pages: 140
Asus ASMB7-iKVM User Manual preview
ASMB7-iKVM
Brand: Asus Pages: 98
Asus ASMB4-IKVM User Manual preview
ASMB4-IKVM
Brand: Asus Pages: 84
EVS XSnano Configuration Manual preview
XSnano
Brand: EVS Pages: 198
Promise Technology ConnectStor II User Manual preview
ConnectStor II
Brand: Promise Technology Pages: 86
Promise Technology VTRAK J300S Quick Start Manual preview
VTRAK J300S
Brand: Promise Technology Pages: 116
Axis AXIS 570 User Manual preview
AXIS 570
Brand: Axis Pages: 316
pachanko MINI User Manual preview
MINI
Brand: pachanko Pages: 56
ASUSTOR AS7110T Memory Installation Manual preview
AS7110T
Brand: ASUSTOR Pages: 11
Eelectron IN00B02WEB Configuration Manual preview
IN00B02WEB
Brand: Eelectron Pages: 42
Eelectron HORIZONE Commissioning Instructions preview
HORIZONE
Brand: Eelectron Pages: 113
Skybox Securoty Appliance 8000 Quick Start Manual preview
Appliance 8000
Brand: Skybox Securoty Pages: 73
Intel SE7520AF2 Operating Manual preview
SE7520AF2
Brand: Intel Pages: 34
Intel S875WP1-E Specification preview
S875WP1-E
Brand: Intel Pages: 117
Ampair IntesisBox User Manual preview
IntesisBox
Brand: Ampair Pages: 26

Brands by name

Popular brands

Load more brands