manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Clear the error log.

4. Run the test again.

5. Make sure that the drive firmware is at the latest level.

6. Rerun the test after upgrading to the latest firmware level.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-902-000 : Tape Test Failed

Tape Test Failed. Media is not detected.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Make sure that the drive firmware is at the latest level.

4. Rerun the test after upgrading to the latest firmware level.

5. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-903-000 : Tape Test Failed

Tape Test Failed. Media is not detected.

Appendix C. DSA diagnostic test results

1183

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Mako 6500 Setup & Configuration Instructions Manual preview
6500
Brand: Mako Pages: 56
NComputing L130 User Manual preview
L130
Brand: NComputing Pages: 95
Far south networks Com.X1 PBX Getting Started preview
Com.X1 PBX
Brand: Far south networks Pages: 4
IBM eServer BladeCenter HS20Type 8832 Maintenance And Troubleshooting Manual preview
eServer BladeCenter HS20Type 8832
Brand: IBM Pages: 158
Digital Equipment DECserver 90TL Owner'S Manual preview
DECserver 90TL
Brand: Digital Equipment Pages: 73
IEI Technology AVL-2000PLUS User Manual preview
AVL-2000PLUS
Brand: IEI Technology Pages: 34
Altos R380 F5 User Manual preview
R380 F5
Brand: Altos Pages: 93
IBM 9009-41G Manual preview
9009-41G
Brand: IBM Pages: 36
Fujitsu PRIMERGY TX140 S2 Operating Manual preview
PRIMERGY TX140 S2
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY TX150 S3 Options Manual preview
PRIMERGY TX150 S3
Brand: Fujitsu Pages: 95
Fujitsu PRIMERGY TX150 S6 Options Manual preview
PRIMERGY TX150 S6
Brand: Fujitsu Pages: 118
Fujitsu primergy TX150 User Manual preview
primergy TX150
Brand: Fujitsu Pages: 305
Fujitsu PRIMERGY TX150 S6 Operating Manual preview
PRIMERGY TX150 S6
Brand: Fujitsu Pages: 127
Fujitsu PRIMERGY TX140 S2 Upgrade And Maintenance Manual preview
PRIMERGY TX140 S2
Brand: Fujitsu Pages: 332
Fujitsu PRIMERGY TX150 S4 Options Manual preview
PRIMERGY TX150 S4
Brand: Fujitsu Pages: 97
Fujitsu PRIMERGY TX150 S7 Operating Manual preview
PRIMERGY TX150 S7
Brand: Fujitsu Pages: 120
Fujitsu PRIMERGY TX140 S1p Datasheet preview
PRIMERGY TX140 S1p
Brand: Fujitsu Pages: 9
HP ProLiant DL100 G2 DPSS Administration Manual preview
ProLiant DL100 G2 DPSS
Brand: HP Pages: 155

Brands by name

Popular brands

Load more brands