manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

0000

0000

0000

0000

0000

0000

0000

0000

0000

0000

Release tab

Figure 172. DVD drive removal

Step 5.

Slide the drive retention clip from the side of the drive. Save the clip to use when you install the
replacement drive or replace the DVD drive filler panel.

Alignment pins

Drive retention clip

Figure 173. DVD drive retention clip removal

Step 6.

Attach the drive retention clip to the side of the DVD drive filler panel that you removed.

Step 7.

Slide the DVD drive filler panel into the DVD drive bay until the DVD drive filler panel clicks into place.

Step 8.

If you are instructed to return the DVD drive, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Replacing a DVD drive

Use this information to install a DVD drive.

The following notes describe the type of drives that the server supports and other information that you must
consider when you install a drive. For a list of supported drives, see http://www.lenovo.com/ serverproven/.

• Locate the documentation that comes with the drive and follow those instructions in addition to the

instructions in this chapter.

• Make sure that you have all the cables and other equipment that are specified in the documentation that

comes with the drive.

• The server supports one ultra-slim SATA optical drive.

To install an optional DVD drive, complete the following steps:

Chapter 6

.

Removing and replacing components

257

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Basalte CORE PLUS Installation Manual preview
CORE PLUS
Brand: Basalte Pages: 2
Vxl Itona TC73yy Hardware User'S Manual preview
Itona TC73yy
Brand: Vxl Pages: 19
Omega DPi8 User Manual preview
DPi8
Brand: Omega Pages: 49
Iwatsu ENTERPRISE 5.0 Owner'S Manual preview
ENTERPRISE 5.0
Brand: Iwatsu Pages: 338
Patton electronics EtherBITS 2285 Getting Started Manual preview
EtherBITS 2285
Brand: Patton electronics Pages: 121
Fastora Fastora NAS T2 Hardware Installation Manual preview
Fastora NAS T2
Brand: Fastora Pages: 24
7starlake SCH-401 User Manual preview
SCH-401
Brand: 7starlake Pages: 67
Moxa Technologies NPort P5250A Series Quick Installation Manual preview
NPort P5250A Series
Brand: Moxa Technologies Pages: 2
Thecus N12000 series User Manual preview
N12000 series
Brand: Thecus Pages: 120
Raritan Dominion SX II User Manual preview
Dominion SX II
Brand: Raritan Pages: 99
TRENDnet TS-U100 - NAS Server - USB User Manual preview
TS-U100 - NAS Server - USB
Brand: TRENDnet Pages: 47
Obvius, LLC AcquiLite A7810-0 Installation And Operation Manual preview
AcquiLite A7810-0
Brand: Obvius, LLC Pages: 29
Supero SuperServer 5013G-M User Manual preview
SuperServer 5013G-M
Brand: Supero Pages: 104
IBM eServer xSeries 335 Type 8676 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 335 Type 8676
Brand: IBM Pages: 178
Boundless ADDS 6700 User Manual preview
ADDS 6700
Brand: Boundless Pages: 33
HP AlphaServer ES47 Installation Manual preview
AlphaServer ES47
Brand: HP Pages: 76
HP AlphaServer GS80 Upgrade Manual preview
AlphaServer GS80
Brand: HP Pages: 88
HP 16-way Specification preview
16-way
Brand: HP Pages: 39

Brands by name

Popular brands

Load more brands