Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 1012

Page: 1012 / 1222

•

816f0a0c-200fffff : An Over-Temperature Condition has been removed on the

[PhysicalMemoryElementName] on Subsystem [MemoryElementName]. (DIMM 15)

This message is for the use case when an implementation has detected an Over Temperature Condition
for Memory that has been Removed.

May also be shown as 816f0a0c200fffff or 0x816f0a0c200fffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0147

User Response

No action; information only.

•

816f0a0c-2010ffff : An Over-Temperature Condition has been removed on the

[PhysicalMemoryElementName] on Subsystem [MemoryElementName]. (DIMM 16)

This message is for the use case when an implementation has detected an Over Temperature Condition
for Memory that has been Removed.

May also be shown as 816f0a0c2010ffff or 0x816f0a0c2010ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0147

User Response

No action; information only.

1000

Lenovo System x3650 M4 Installation and Service Guide

«
...
1010
1011
1012
1013
1014
...
»

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands