manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

SAS
signal
cable

Power
cable

Configuration
cable

Hard disk drive
backplane

Figure 64. Hard disk drive backplane removal

a.

From backplane 1, disconnect the following cables in the order listed:

• Power cable 1

• SAS signal cable 2

• Configuration cable 3

b.

Lift backplane 1 out of the server by pulling it toward the rear of the server and then lifting it up.

Step 9.

Install the new backplane in slot 2:

a.

Connect two SAS signal cables (610 mm) to new backplane 2. The new backplane comes
with the option kit.

b.

Connect the configuration cable to backplane 2.

c.

Screw the SEARAY cable to backplane 2 as shown in the following illustration and connect
two SAS signal cables to backplane 1.

Chapter 2

.

Installing optional devices

81

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Paradyne FrameSaver SLV 9126 Installation Instructions Manual preview
FrameSaver SLV 9126
Brand: Paradyne Pages: 24
YOKOGAWA SMARTDAG+ GM10 User Manual preview
SMARTDAG+ GM10
Brand: YOKOGAWA Pages: 22
HPE SimpliVity 2600 Gen10 Installation And Maintenance Manual preview
SimpliVity 2600 Gen10
Brand: HPE Pages: 37
Supermicro SUPERSERVER 1015B-3 User Manual preview
SUPERSERVER 1015B-3
Brand: Supermicro Pages: 98
Dell Force10 MXL Blade Specifications preview
Force10 MXL Blade
Brand: Dell Pages: 2
Thecus N299 User Manual preview
N299
Brand: Thecus Pages: 94
RSA Security SILVERSTREAM 3.75 User Manual preview
SILVERSTREAM 3.75
Brand: RSA Security Pages: 11
BITMAIN T19 Hydro Server Installation Manual preview
T19 Hydro Server
Brand: BITMAIN Pages: 17
Viavi G4-40G-010-384T Manual preview
G4-40G-010-384T
Brand: Viavi Pages: 12
Red Hat DIRECTORY SERVER 8.0 Installation Manual preview
DIRECTORY SERVER 8.0
Brand: Red Hat Pages: 128
Gigabyte G221-Z30 User Manual preview
G221-Z30
Brand: Gigabyte Pages: 143
ZLAN ZLAN9153 User Manual preview
ZLAN9153
Brand: ZLAN Pages: 16
ZLAN ZLAN8303 User Manual preview
ZLAN8303
Brand: ZLAN Pages: 17
Converters.TV 515 Operation Manual preview
515
Brand: Converters.TV Pages: 20
Micron NetFRAME 2100 Series Product Manual preview
NetFRAME 2100 Series
Brand: Micron Pages: 178
Supero AS-1010S-T User Manual preview
AS-1010S-T
Brand: Supero Pages: 100
Supero AS-1011M-UR User Manual preview
AS-1011M-UR
Brand: Supero Pages: 104
Supero AS 4040C-TR User Manual preview
AS 4040C-TR
Brand: Supero Pages: 104

Brands by name

Popular brands

Load more brands