manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Table 21. Light path diagnostics panel LEDs (continued)

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• If an action step is preceded by "(trained technician only)," that step must be performed only by a trained

technician.

LED

Description

Action

a. Replace the hard disk drive.

b. Replace the hard disk drive backplane.

5. If the problem remains, go to

http://www.ibm.com/support/entry/portal/docdisplay?
lndocid=SERV-CALL.

Power-supply LEDs

The following minimum configuration is required for the server to start.
• One microprocessor in microprocessor socket 1
• One 2 GB DIMM on the system board
• One power supply
• Power cord
• Four cooling fans (fan 1, 2, 3, and 5)
• One PCI riser-card assembly in PCI connector 1

AC power-supply LEDs

The following minimum configuration is required for the DC LED on the power supply to be lit:
• Power supply
• Power cord

Note:

You must turn on the server for the DC LED on the power supply to be lit.

The following illustration shows the locations of the power-supply LEDs on the ac power supply.

000

000

000

00

00

00

00

00

00

000

00

000

000

0000

Figure 143. AC power-supply LEDs

The following table describes the problems that are indicated by various combinations of the power-supply
LEDs on an ac power supply and suggested actions to correct the detected problems.

Chapter 4

.

Troubleshooting

179

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM eServer 200 xSeries User Reference Manual preview
eServer 200 xSeries
Brand: IBM Pages: 128
IBM eServer 232 xSeries User Reference Manual preview
eServer 232 xSeries
Brand: IBM Pages: 174
IBM Z10 BUISNESS CLASS Z10 BC Reference Manual preview
Z10 BUISNESS CLASS Z10 BC
Brand: IBM Pages: 67
IBM x3450 - System - 7948 Quick Start Manual preview
x3450 - System - 7948
Brand: IBM Pages: 2
Hamlet HPS01UU2 User Manual preview
HPS01UU2
Brand: Hamlet Pages: 76
Fujitsu PRIMERGY Econel 230R S1 Service Supplement Manual preview
PRIMERGY Econel 230R S1
Brand: Fujitsu Pages: 53
Fujitsu Primergy ECONEL 100 S2 Start Manual preview
Primergy ECONEL 100 S2
Brand: Fujitsu Pages: 8
Fujitsu PRIMERGY Econel 200 S2 Options Manual preview
PRIMERGY Econel 200 S2
Brand: Fujitsu Pages: 65
Fujitsu PRIMERGY MX130 S1 Operating Manual preview
PRIMERGY MX130 S1
Brand: Fujitsu Pages: 85
Fujitsu PRIMERGY Econel 100 Operating Manual preview
PRIMERGY Econel 100
Brand: Fujitsu Pages: 64
Fujitsu primergy h250 Manual preview
primergy h250
Brand: Fujitsu Pages: 105
Fujitsu Primergy N800 Manual preview
Primergy N800
Brand: Fujitsu Pages: 142
Fujitsu PRIMERGY GX2460 M1 Upgrade And Maintenance Manual preview
PRIMERGY GX2460 M1
Brand: Fujitsu Pages: 251
Fujitsu PRIMERGY MX130 S2 Upgrade and maintenance manua Upgrade And Maintenance Manual preview
PRIMERGY MX130 S2 Upgrade and maintenance manua
Brand: Fujitsu Pages: 256
Fujitsu Primergy RX100 S2 User Manual preview
Primergy RX100 S2
Brand: Fujitsu Pages: 275
Fujitsu Primergy RX100 S3 User Manual preview
Primergy RX100 S3
Brand: Fujitsu Pages: 287
Fujitsu PRIMERGY ECONEL30 Configuration Manual preview
PRIMERGY ECONEL30
Brand: Fujitsu Pages: 11
Dell E74S Reference Manual preview
E74S
Brand: Dell Pages: 25

Brands by name

Popular brands

Load more brands