manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Yes

Automatically notify support

No

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0174

User Response

1. Make sure that the RAID adapter firmware and hard disk drive firmware are at the latest level.

2. Make sure that the SAS cable is connected correctly.

3.

Replace the SAS cable.

4. Check backplane cable connection.

5.

Replace the RAID adapter.

6. Replace the hard disk drive that is indicated by a lit status LED.

•

806f050d-0407ffff : Array [ComputerSystemElementName] is in critical condition. (Drive 7)

This message is for the use case when an implementation has detected that an Array is Critical.

May also be shown as 806f050d0407ffff or 0x806f050d0407ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0174

User Response

1. Make sure that the RAID adapter firmware and hard disk drive firmware are at the latest level.

2. Make sure that the SAS cable is connected correctly.

3.

Replace the SAS cable.

4. Check backplane cable connection.

5.

Replace the RAID adapter.

Appendix A. Integrated management module II (IMM2) error messages

649

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Supermicro SuperServer E100-8Q User Manual preview
SuperServer E100-8Q
Brand: Supermicro Pages: 48
Bull NovaScale R410B F2 Getting Started preview
NovaScale R410B F2
Brand: Bull Pages: 38
Supero SuperServer 1026T-M3 User Manual preview
SuperServer 1026T-M3
Brand: Supero Pages: 104
DNP WPS Pro EU User Manual preview
WPS Pro EU
Brand: DNP Pages: 93
IBM eserver iSeries 270 Installation Manual preview
eserver iSeries 270
Brand: IBM Pages: 40
Polycom ReadiManagerSE200 Brochure preview
ReadiManagerSE200
Brand: Polycom Pages: 4
Black Box les1208A Manual preview
les1208A
Brand: Black Box Pages: 4
Black Box LES1202A Quick Start Manual preview
LES1202A
Brand: Black Box Pages: 12
Promise Technology VTRAK M210i Product Manual preview
VTRAK M210i
Brand: Promise Technology Pages: 318
IBM 7145 Installation And User Manual preview
7145
Brand: IBM Pages: 136
Nestbox C5A50 Quick Start Manual preview
C5A50
Brand: Nestbox Pages: 4
MPC netframe 1610 Quick Start Manual preview
netframe 1610
Brand: MPC Pages: 72
Stentofon alphaCom XE Installation, Configuration & Operation preview
alphaCom XE
Brand: Stentofon Pages: 68
Oracle Solaris Cluster 3.3 System Manual preview
Solaris Cluster 3.3
Brand: Oracle Pages: 56
ClearCube SmartVDI-110 Quick Start Manual preview
SmartVDI-110
Brand: ClearCube Pages: 10
Gateway ALR 9200 Maintaining And Troubleshooting preview
ALR 9200
Brand: Gateway Pages: 226
Gigabyte R182-N20 User Manual preview
R182-N20
Brand: Gigabyte Pages: 114
Repotec RP-UB2801A Quick Installation Manual preview
RP-UB2801A
Brand: Repotec Pages: 12

Brands by name

Popular brands

Load more brands