Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 882

Page: 882 / 1222

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0169

User Response

No action; information only.

•

816f020d-0418ffff : Failure no longer Predicted on drive [StorageVolumeElementName] for array

[ComputerSystemElementName]. (Drive 24)

This message is for the use case when an implementation has detected an Array Failure is no longer
Predicted.

May also be shown as 816f020d0418ffff or 0x816f020d0418ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0169

User Response

No action; information only.

•

816f020d-0419ffff : Failure no longer Predicted on drive [StorageVolumeElementName] for array

[ComputerSystemElementName]. (Drive 25)

This message is for the use case when an implementation has detected an Array Failure is no longer
Predicted.

May also be shown as 816f020d0419ffff or 0x816f020d0419ffff

870

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands