Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 146

Page: 146 / 1222

Figure 129. Thermal grease

Remove the plastic protective cover from the bottom of the heat sink.

Position the heat sink over the microprocessor. The heat sink is keyed to assist with proper
alignment.

Figure 130. Heat sink installation

Align and place the heat sink on top of the microprocessor in the retention bracket, thermal
material side down.

Press firmly on the heat sink.

Rotate the heat sink retention module release lever to the closed position and hook it
underneath the lock tab.

Step 11. If you installed the second microprocessor, install the fourth fan (see “Replacing a hot-swap

fan” on page 312).

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on
page 136.

134

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands