Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 925

Page: 925 / 1222

•

816f050c-2016ffff : Memory Logging Limit Removed for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (DIMM 22)

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Removed.

May also be shown as 816f050c2016ffff or 0x816f050c2016ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0145

User Response

No action; information only.

•

816f050c-2017ffff : Memory Logging Limit Removed for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (DIMM 23)

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Removed.

May also be shown as 816f050c2017ffff or 0x816f050c2017ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0145

User Response

No action; information only.

Appendix A. Integrated management module II (IMM2) error messages

913

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands