Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 565

Page: 565 / 1222

•

806f010d-2b81ffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (FDIMM Stat)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d2b81ffff or 0x806f010d2b81ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0164

User Response

None

•

806f010f-2201ffff : The System [ComputerSystemElementName] encountered a firmware hang.

(Firmware Error)

This message is for the use case when an implementation has detected a System Firmware Hang.

May also be shown as 806f010f2201ffff or 0x806f010f2201ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

System - Boot failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0186

User Response

1. Make sure the server meets the minimum configuration to start (see Power-supply LEDs).

Appendix A. Integrated management module II (IMM2) error messages

553

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands