Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 556

Page: 556 / 1222

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-0412ffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 18)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d0412ffff or 0x806f010d0412ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-0413ffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Drive 19)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d0413ffff or 0x806f010d0413ffff

544

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands