Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 245 | Manualshive

Page: 245 / 1222

background image

USB cable

Video cable

Figure 149. Front USB and video cables connection

Cabling operator information panel

The internal routing and connectors for the operator information panel.

The following notes describe additional information you must consider when you install or remove the
operator information panel cable:

• You may remove the optional optical drive cable to obtain more room before you install or remove the

operator information panel cable.

• To remove the operator information panel cable, slightly press the cable toward the fan cage; then, pull to

remove the cable from the connector on the system board. Pulling the cable out of the connector by
excessive force might cause damage to the cable or connector.

• To connect the operator information panel cable on the system board, press evenly on the cable. Pressing

on one side of the cable might cause damage to the cable or connector.

Attention:

Failing to install or remove the cable with care may damage the connectors on the system board.

Any damage to the connectors may require replacing the system board.

Removing and replacing components

233

«
...
243
244
245
246
247
...
»

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Brand: Far south networks Pages: 4

Brand: Sun Fire Pages: 66

Flex System x240 Compute Node

Brand: IBM Pages: 28

Brand: Oki Pages: 2

Brand: IBM Pages: 100

Brand: Arris Pages: 6

Brand: Hitachi Pages: 208

Brand: Hitachi Pages: 36

Brand: Asus Pages: 98

Brand: Asus Pages: 84

Brand: Antrica Pages: 68

Brand: Artesyn Embedded Technology Pages: 2

Brand: QNAP Pages: 58

Brand: TAG Pages: 84

SafeNet ProtectServer PCIe HSM 5.4

Brand: Thales Pages: 27

Brand: Promise Technology Pages: 86

Brand: Promise Technology Pages: 116

Brand: ASUSTOR Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands