manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

22

CIM Information

Prefix:

IMM

ID:

0137

User Response

1. Turn off the server and disconnect it from the power source. You must disconnect the server

from ac power to reset the IMM.

2. After 45 seconds, reconnect the server to the power source and turn on the server.

3.

Retry the operation.

•

4000008a-00000000 : Management Controller [arg1]: Configuration restoration from a file by

user [arg2] failed to start.

This message is for the use case where a user restores a Management Controller configuration from
a file and the restoration fails to start.

May also be shown as 4000008a00000000 or 0x4000008a00000000

Severity

Error

Serviceable

No

Automatically notify support

No

Alert Category

System - Other

SNMP Trap ID

22

CIM Information

Prefix:

IMM

ID:

0138

User Response

1. Turn off the server and disconnect it from the power source. You must disconnect the server

from ac power to reset the IMM.

2. After 45 seconds, reconnect the server to the power source and turn on the server.

3.

Retry the operation.

•

4000008b-00000000 : One or more of the Storage Management IP addresses has changed.

This message is for the use case where an IP address for the Storage Management has changed

May also be shown as 4000008b00000000 or 0x4000008b00000000

Severity

422

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Qlogic iSR6200 Quick Start Manual preview
iSR6200
Brand: Qlogic Pages: 20
IBM x3100 M5 Type 5457 Installation And Service Manual preview
x3100 M5 Type 5457
Brand: IBM Pages: 688
IBM 847620U - Netfinity 3000 - 20U Hardware Maintenance Manual preview
847620U - Netfinity 3000 - 20U
Brand: IBM Pages: 270
Discover Video Devos 4 User Manual preview
Devos 4
Brand: Discover Video Pages: 148
NEC Express 320Ma Read Me First preview
Express 320Ma
Brand: NEC Pages: 10
Bosch DL380 Gen 10 AI Quick Installation Manual preview
DL380 Gen 10 AI
Brand: Bosch Pages: 18
Bosch DIP-61F0-00N Installation Manual preview
DIP-61F0-00N
Brand: Bosch Pages: 48
Bosch PRA-APAS Configuration Manual preview
PRA-APAS
Brand: Bosch Pages: 44
QNAP TS-h2490FU User Manual preview
TS-h2490FU
Brand: QNAP Pages: 58
EVS XT-3 Hardware Technical Reference Manual preview
XT-3
Brand: EVS Pages: 126
Viavi G4-20G-010-192T Manual preview
G4-20G-010-192T
Brand: Viavi Pages: 12
Planet NAS-7102 User Manual preview
NAS-7102
Brand: Planet Pages: 68
Gigabyte G492-ZD0 User Manual preview
G492-ZD0
Brand: Gigabyte Pages: 152
Tektronix MSO54 Programmer'S Manual preview
MSO54
Brand: Tektronix Pages: 1026
Dell EMC PowerEdge C6420 Manual preview
PowerEdge C6420
Brand: Dell EMC Pages: 53
Dell EMC PowerEdge M640 Installation And Service Manual preview
PowerEdge M640
Brand: Dell EMC Pages: 110
Dell EMC PowerEdge FC430 Owner'S Manual preview
PowerEdge FC430
Brand: Dell EMC Pages: 117
Dell EMC PowerEdge R640 Installation And Service Manual preview
PowerEdge R640
Brand: Dell EMC Pages: 174

Brands by name

Popular brands

Load more brands