manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

409-906-000 : Nvidia::DiagnosticServiceProvider::Binomial Test Failed

Nvidia GPU Binomial Test Failed.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Verify that the GPU is seated in the PCIe slot correctly by reseating the GPU. Then power cycle

the system.

2. Verify that the power connectors to the GPU are connected firmly. Then power cycle the system.

3. Run nvidia-smi -q In some cases this will report a poorly connected power cable.

4. Rerun the diagnostics, using the same GPU, on system that is known to be working. A variety of

system issues can cause diagnostic failure.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA optical drive test results

The following messages can result when you run the optical drive test.

Test results for the DSA optical drive test

The following messages can result when you run the DSA optical drive test.

•

215-000-000 : Optical Drive Test Passed

Optical Drive Test Passed.

Recoverable

1162

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM Enterprise Server S80 User Manual preview
Enterprise Server S80
Brand: IBM Pages: 282
Xerox Phaser EX7750 Configuration Manual preview
Phaser EX7750
Brand: Xerox Pages: 220
Xerox Phaser EX7750 Quick Start Manual preview
Phaser EX7750
Brand: Xerox Pages: 28
Xerox DocuPrint 100MX Install Manual preview
DocuPrint 100MX
Brand: Xerox Pages: 2
Supero SUPERO SuperServer 6026TT-GIBQRF User Manual preview
SUPERO SuperServer 6026TT-GIBQRF
Brand: Supero Pages: 104
IBM Flex System p270 Compute Node Installation And Service Manual preview
Flex System p270 Compute Node
Brand: IBM Pages: 510
NAIM UNITISERVE - Quick Start Manual preview
UNITISERVE -
Brand: NAIM Pages: 18
Sun Oracle SPARC T3-2 Service Manual preview
SPARC T3-2
Brand: Sun Oracle Pages: 222
BRONKHORST FlowDDE Instruction Manual preview
FlowDDE
Brand: BRONKHORST Pages: 19
IBM eserver xSeries 350 User Reference Manual preview
eserver xSeries 350
Brand: IBM Pages: 174
Xerox CSX 2000 Reference Manual preview
CSX 2000
Brand: Xerox Pages: 13
Xerox 6100BD - Phaser Color Laser Printer Installation Manual preview
6100BD - Phaser Color Laser Printer
Brand: Xerox Pages: 34
Xerox 6100BD - Phaser Color Laser Printer Operator'S Manual preview
6100BD - Phaser Color Laser Printer
Brand: Xerox Pages: 140
Bosanova RBT-420 Specifications preview
RBT-420
Brand: Bosanova Pages: 2
Bosanova RBT-320 Specifications preview
RBT-320
Brand: Bosanova Pages: 2
Habey FW-1109 Quick Setup Manual preview
FW-1109
Brand: Habey Pages: 3
Multitech TalkAnytime TA2410 User Manual preview
TalkAnytime TA2410
Brand: Multitech Pages: 235
Meinberg LANTIME IMS-M500 Manual preview
LANTIME IMS-M500
Brand: Meinberg Pages: 63

Brands by name

Popular brands

Load more brands