manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Table 29. Supported microprocessors (continued)

Microprocessor description

Option part number

FRU part number

Intel Xeon Processor E5-2690 v2,
3.0 GHz, 25 MB, 1866 MHz, 130 W
(10-core)

46W4377

00Y2787

Intel Xeon Processor E5-2697 v2,
2.7 GHz, 30 MB, 1866 MHz, 130 W
(12-core)

46W4374

00Y2777

• Flash DIMM configuration supports one mezz adapter.

Table 30. Supported adapter

Adpater description

Option part number

FRU part number

Intel x520 dual port 10GbE SFP+
embedded adapter

49Y7980

49Y7982

• For detailed Flash DIMM installation sequence, go to “DIMM installation sequence” on page 54.

Notes:

1. You can install DIMMs for microprocessor 2 as soon as you install microprocessor 2; you do not have

to wait until all of the DIMM slots for microprocessor 1 are filled.

2. DIMM slots 13-24 are reserved for microprocessor 2; thus, DIMM slots 13-24 are enabled when

microprocessor 2 is installed.

The following illustration shows the location of the DIMM connectors on the system board.

Figure 185. DIMM connectors location

270

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Xerox CX Visual Reference Manual preview
CX
Brand: Xerox Pages: 12
Belkin F1UP0001uk Basic Manual preview
F1UP0001uk
Brand: Belkin Pages: 8
TYANO TS65A-B8036 Service Engineer'S Manual preview
TS65A-B8036
Brand: TYANO Pages: 102
IBM System x3250 Specifications preview
System x3250
Brand: IBM Pages: 2
IBM System x3100 M4 Product Manual preview
System x3100 M4
Brand: IBM Pages: 35
IBM eServer xSeries 345 Type 8670 Installation Manual preview
eServer xSeries 345 Type 8670
Brand: IBM Pages: 71
IBM eServer 445 xSeries Installation Manual preview
eServer 445 xSeries
Brand: IBM Pages: 124
IBM pSeries 615 Model 6C3 User Manual preview
pSeries 615 Model 6C3
Brand: IBM Pages: 208
IBM Multiprise 3000 Reference Manual preview
Multiprise 3000
Brand: IBM Pages: 264
IBM Redboks System x3550 M4 Installation And Service Manual preview
Redboks System x3550 M4
Brand: IBM Pages: 820
EVS XSnano Configuration Manual preview
XSnano
Brand: EVS Pages: 198
Chip PC Xtreme PC NG6452 Specifications preview
Xtreme PC NG6452
Brand: Chip PC Pages: 4
IBM @server iSeries User Manual preview
@server iSeries
Brand: IBM Pages: 294
Skybox Securoty Appliance 8000 Quick Start Manual preview
Appliance 8000
Brand: Skybox Securoty Pages: 73
QNAP NAS TS-877XU-RP-3600-8G-US Quick Installation Manual preview
NAS TS-877XU-RP-3600-8G-US
Brand: QNAP Pages: 12
QNAP Nextephive User Manual preview
Nextephive
Brand: QNAP Pages: 15
B+B SmartWorx VESP211 Series Quick Start Manual preview
VESP211 Series
Brand: B+B SmartWorx Pages: 2
Iomega 1562 Installation Manual preview
1562
Brand: Iomega Pages: 23

Brands by name

Popular brands

Load more brands