Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 944

Page: 944 / 1222

May also be shown as 816f06072584ffff or 0x816f06072584ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0817

User Response

No action; information only. One of the CPUs :

•

816f0608-1301ffff : [PowerSupplyElementName] Configuration is OK. (PS Configuration)

This message is for the use case when an implementation when a Power Supply configuration is OK.

May also be shown as 816f06081301ffff or 0x816f06081301ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Power

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0105

User Response

No action; information only.

•

816f060d-0400ffff : Array in system [ComputerSystemElementName] has been restored. (Drive 0)

This message is for the use case when an implementation has detected that a Failed Array has been
Restored.

May also be shown as 816f060d0400ffff or 0x816f060d0400ffff

932

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands