manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Configuration changes, such as added devices or adapter firmware updates, and firmware or application
code problems can cause the server to fail POST (the power-on self-test). If this occurs, the server responds
in either of the following ways:

• The server restarts automatically and attempts POST again.

• The server hangs, and you must manually restart the server for the server to attempt POST again.

After a specified number of consecutive attempts (automatic or manual), the Nx-boot failure feature causes
the server to revert to the default UEFI configuration and start the Setup utility so that you can make the
necessary corrections to the configuration and restart the server. If the server is unable to successfully
complete POST with the default configuration, there might be a problem with the system board.

To specify the number of consecutive restart attempts that will trigger the Nx-boot failure feature, in the
Setup utility, click

System Settings

➙

Recovery

➙

POST Attempts

➙

POST Attempts Limit

. The available

options are 3, 6, 9, and 255 (disable Nx-boot failure).

Chapter 4

.

Troubleshooting

213

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IEI Technology PUZZLE-IN003A User Manual preview
PUZZLE-IN003A
Brand: IEI Technology Pages: 89
IBM System x3250 M3 Type 4251 Manual preview
System x3250 M3 Type 4251
Brand: IBM Pages: 32
BlueBroadcaster iSENDER User Manual preview
iSENDER
Brand: BlueBroadcaster Pages: 21
NETGEAR ReadyNAS 3220 Series Datasheet preview
ReadyNAS 3220 Series
Brand: NETGEAR Pages: 4
Fujitsu GP 7000F Manual preview
GP 7000F
Brand: Fujitsu Pages: 200
3onedata NP301 User Manual preview
NP301
Brand: 3onedata Pages: 24
QNAP TS-130 User Manual preview
TS-130
Brand: QNAP Pages: 39
Advantech EKI-1511X User Manual preview
EKI-1511X
Brand: Advantech Pages: 76
Advantech ASMB-781 User Manual preview
ASMB-781
Brand: Advantech Pages: 92
Kramer KDS-8-MNGR User Manual preview
KDS-8-MNGR
Brand: Kramer Pages: 72
Compatible Systems IntraPort Enterprise-2 User Manual preview
IntraPort Enterprise-2
Brand: Compatible Systems Pages: 43
SSS Siedle Access Server M Upgrade Instructions preview
Access Server M
Brand: SSS Siedle Pages: 28
Abekas Mira User'S Operation Manual preview
Mira
Brand: Abekas Pages: 382
GIGA-BYTE TECHNOLOGY R282-P92 User Manual preview
R282-P92
Brand: GIGA-BYTE TECHNOLOGY Pages: 96
GIGA-BYTE TECHNOLOGY R282-P91 User Manual preview
R282-P91
Brand: GIGA-BYTE TECHNOLOGY Pages: 99
GIGA-BYTE TECHNOLOGY G292-Z20 User Manual preview
G292-Z20
Brand: GIGA-BYTE TECHNOLOGY Pages: 142
D-Link DSN-6020 User Manual preview
DSN-6020
Brand: D-Link Pages: 146
QUANTA D51BP-1U User Manual preview
D51BP-1U
Brand: QUANTA Pages: 34

Brands by name

Popular brands

Load more brands