manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Step 6.

Remove the heat sink.

Attention:

Do not touch the thermal material on the bottom of the heat sink. Touching the thermal

material will contaminate it. If the thermal material on the microprocessor or heat sink becomes
contaminated, you must wipe off the contaminated thermal material on the microprocessor or heat
sink with the alcohol wipes and reapply clean thermal grease to the heat sink.

a.

Open the heat sink retention module release lever to the fully open position.

b.

Lift the heat sink out of the server. After removal, place the heat sink (with the thermal grease
side up) on a clean, flat surface.

Figure 236. Heat sink removal

Step 7.

Open the microprocessor socket release levers and retainer.

Microprocessor

Microprocessor
release lever

Microprocessor
release lever

Figure 237. Microprocessor socket levers and retainer disengagement

a.

Identify which release lever is labeled as the first release lever to open and open it.

b.

Open the second release lever on the microprocessor socket.

c.

Open the microprocessor retainer.

Chapter 6

.

Removing and replacing components

327

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

NEC Express5800/T110g-E Quick Start Manual preview
Express5800/T110g-E
Brand: NEC Pages: 2
Xerox Phaser EX7750 Configuration Manual preview
Phaser EX7750
Brand: Xerox Pages: 220
Xerox Phaser EX7750 Quick Start Manual preview
Phaser EX7750
Brand: Xerox Pages: 28
Xerox DocuPrint 100MX Install Manual preview
DocuPrint 100MX
Brand: Xerox Pages: 2
Sollae Systems CSE-H20 User Manual preview
CSE-H20
Brand: Sollae Systems Pages: 45
Planet FPS-1010M Quick Installation Manual preview
FPS-1010M
Brand: Planet Pages: 24
LG-Ericsson iPECS-CM Operation Manual preview
iPECS-CM
Brand: LG-Ericsson Pages: 54
Jia Teng Talk Server Pro WP1264 Setting Manual preview
Talk Server Pro WP1264
Brand: Jia Teng Pages: 23
Planex mini-mfp Quick Installation Manual preview
mini-mfp
Brand: Planex Pages: 16
Gigabyte R181-2A0 Service Manual preview
R181-2A0
Brand: Gigabyte Pages: 127
Inspur NF8260M5 User Manual preview
NF8260M5
Brand: Inspur Pages: 205
Oracle SPARC M8-8 Getting Started Manual preview
SPARC M8-8
Brand: Oracle Pages: 6
Oracle Exalytics In-Memory Machine Owner'S Manual preview
Exalytics In-Memory Machine
Brand: Oracle Pages: 85
Interactive Intelligence Audiocodes Mediant 800 based Installation And Configuration Manual preview
Audiocodes Mediant 800 based
Brand: Interactive Intelligence Pages: 33
Gigabyte R272-P30 User Manual preview
R272-P30
Brand: Gigabyte Pages: 84
Gigabyte R261-3C0 User Manual preview
R261-3C0
Brand: Gigabyte Pages: 107
Gigabyte R182-M80 User Manual preview
R182-M80
Brand: Gigabyte Pages: 109
Gigabyte R182-Z93 User Manual preview
R182-Z93
Brand: Gigabyte Pages: 144

Brands by name

Popular brands

Load more brands