manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

• When you route cables, do not block any connectors or the ventilated space around any of

the fans.

• Make sure that cables are not routed on top of components that are under the PCI riser-card

assembly.

• Make sure that cables are not pinched by the server components.

Step 10. Align the PCI riser-card assembly with the selected PCI riser-card connector on the system board.

0

0

0

0

00

00

00

0000

0000

0000

0000

0000

0000

0000

0000

000

000

000

000000

000000

000000

00

0000

0000

0000

0000

0000

0000

000000

000000

000000

00

0000

0000

0000

PCI riser-card
assembly 2

PCI riser-card
assembly 1

Figure 47. Installing PCI riser-card assembly

• PCI riser-card connector 1: Carefully fit the two alignment slots on the side of the assembly

onto the two alignment brackets in the side of the chassis; align the rear of the assembly with
the guides on the rear of the server.

• PCI riser-card connector 2: Carefully align the bottom edge (the contact edge) of the riser-card

assembly with the PCI riser-card connector on the system board; align the rear of the assembly
with the guides on the rear of the server.

Step 11. Press down on the assembly. Make sure that the riser-card assembly is fully seated in the PCI

riser-card connector on the system board.

Step 12. Perform any configuration tasks that are required for the adapter.

Chapter 2

.

Installing optional devices

63

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM 8841 - eServer xSeries 236 Installation Manual preview
8841 - eServer xSeries 236
Brand: IBM Pages: 100
NEC Express5800/320Fa-L User Manual preview
Express5800/320Fa-L
Brand: NEC Pages: 406
Seyeon FW3150 User Manual preview
FW3150
Brand: Seyeon Pages: 10
Honeywell HP ProLiant DL360P Gen8 Service Manual preview
HP ProLiant DL360P Gen8
Brand: Honeywell Pages: 67
QNAP Turbo NAS TS-219P Troubleshooting Manual preview
Turbo NAS TS-219P
Brand: QNAP Pages: 49
Xerox CSX 2000 Reference Manual preview
CSX 2000
Brand: Xerox Pages: 13
Xerox 6100BD - Phaser Color Laser Printer Installation Manual preview
6100BD - Phaser Color Laser Printer
Brand: Xerox Pages: 34
Xerox 6100BD - Phaser Color Laser Printer Operator'S Manual preview
6100BD - Phaser Color Laser Printer
Brand: Xerox Pages: 140
Thecus N299 User Manual preview
N299
Brand: Thecus Pages: 94
BITMAIN ANTMINER S19 Pro+ Hydro Installation Manual preview
ANTMINER S19 Pro+ Hydro
Brand: BITMAIN Pages: 17
EVS GX User Manual preview
GX
Brand: EVS Pages: 74
Super SC809LT-780B User Manual preview
SC809LT-780B
Brand: Super Pages: 60
SSS Siedle AS 670-0 S Product Information preview
AS 670-0 S
Brand: SSS Siedle Pages: 12
Webster MultiPort/LT User'S Reference Manual preview
MultiPort/LT
Brand: Webster Pages: 114
BayTech LASERSHARE PS-MIO Owner'S Manual preview
LASERSHARE PS-MIO
Brand: BayTech Pages: 133
UNV DVS4104 Quick Manual preview
DVS4104
Brand: UNV Pages: 27
Gateway 995 User Manual preview
995
Brand: Gateway Pages: 176
Dell EMC E67S Installation And Service Manual preview
E67S
Brand: Dell EMC Pages: 149

Brands by name

Popular brands

Load more brands