Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 142

Page: 142 / 1222

Figure 121. Heat-sink lever rotation

Step 6.

Open the microprocessor socket release levers and retainer:

Figure 122. Microprocessor socket levers and retainer disengagement

Identify which release lever is labeled as the first release lever to open and open it.

Open the second release lever on the microprocessor socket.

Open the microprocessor retainer.

Attention:

Do not touch the connectors on the microprocessor and the microprocessor socket.

Step 7.

Install the microprocessor on the microprocessor socket:

Touch the static-protective package that contains the new microprocessor to any

unpainted

on the chassis or any

unpainted

metal surface on any other grounded rack component; then,

carefully remove the microprocessor from the package.

Release the sides of the cover and remove the cover from the installation tool. The
microprocessor is preinstalled on the installation tool.

130

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands