manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Step 2.

Remove the filler panel from the empty drive bay. Keep the filler panel in a safe place.

Step 3.

Touch the static-protective package that contains the drive to any unpainted metal surface on the
server; then, remove the drive from the package and place it on a static-protective surface.

Step 4.

Install the hard disk drive in the drive bay:

a.

Make sure that the tray handle is in the open (unlocked) position.

b.

Align the drive with the guide rails in the bay.

0000

0000

0000

0000

0000

000

000

000

000

000

Latch

Handle

Filler panel handle

Figure 27. 2.5-inch hot-swap hard disk drives installation

00

00

00

00

00

0

0

0

0

0

000

000

000

000

000

000

000

000

000

0000

0000

0000

0000

Latch

Handle

Filler panel

3.5-inch hot-swap
hard disk drive

Figure 28. 3.5-inch hot-swap hard disk drives installation

c.

Gently push the drive into the bay until the drive stops.

d.

Rotate the tray handle to the closed (locked) position.

e.

Check the hard disk drive status LED to verify that the hard disk drive is operating correctly. If
the yellow hard disk drive status LED of a drive is lit continuously, that drive is faulty and must
be replaced. If the green hard disk drive activity LED is flashing, the drive is being accessed.

Note:

If the server is configured for RAID operation using a ServeRAID adapter, you might

have to reconfigure your disk arrays after you install hard disk drives. See the ServeRAID
adapter documentation for additional information about RAID operation and complete
instructions for using the ServeRAID adapter.

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the
installation” on page 136.

42

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

NEC Express5800/180Ra-7 Datasheet preview
Express5800/180Ra-7
Brand: NEC Pages: 2
NEC Express5800/120Rh-2 Getting Started Manual preview
Express5800/120Rh-2
Brand: NEC Pages: 2
NEC Express5800/120Rh-2 Datasheet preview
Express5800/120Rh-2
Brand: NEC Pages: 2
NEC Express5800/120Rg-1 Datasheet preview
Express5800/120Rg-1
Brand: NEC Pages: 2
NEC Express5800/120Rf-1 Operation Manual preview
Express5800/120Rf-1
Brand: NEC Pages: 21
NEC Express5800/120Ra-1 Release Note preview
Express5800/120Ra-1
Brand: NEC Pages: 6
NEC Express5800/120Mc2 series Datasheet preview
Express5800/120Mc2 series
Brand: NEC Pages: 2
NEC EXPRESS5800/120Le Configuration Manual preview
EXPRESS5800/120Le
Brand: NEC Pages: 56
NEC Express5800 320La Installation Notes preview
Express5800 320La
Brand: NEC Pages: 8
NEC Express5800 120Li Datasheet preview
Express5800 120Li
Brand: NEC Pages: 2
NEC Express5800 120Ed Installation Procedures Manual preview
Express5800 120Ed
Brand: NEC Pages: 29
NEC Active Upgrade Express5800/320Fc Datasheet preview
Active Upgrade Express5800/320Fc
Brand: NEC Pages: 4
NEC 320Fc Read Me First preview
320Fc
Brand: NEC Pages: 10
NEC Express5800/120Rj-2 Configuration Manual preview
Express5800/120Rj-2
Brand: NEC Pages: 18
NEC Express5800/120Rh-1 Configuration Manual preview
Express5800/120Rh-1
Brand: NEC Pages: 20
NEC Bull NovaScale R620 Series User Manual preview
Bull NovaScale R620 Series
Brand: NEC Pages: 346
NEC Express5800 320La User Manual preview
Express5800 320La
Brand: NEC Pages: 206
NEC Express5800/R110j-1 Manual preview
Express5800/R110j-1
Brand: NEC Pages: 30

Brands by name

Popular brands

Load more brands