Lenovo x3650 M4 BD 5466 Installation And Service Manual Download Page 798

Page: 798 / 1222

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only. nvDIMM Flash :

•

8107020f-2582ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (I/O Resources)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 8107020f2582ffff or 0x8107020f2582ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

No action; information only.

•

81070214-2201ffff : Sensor [SensorElementName] has transitioned to a less severe state from

critical. (TPM Lock)

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702142201ffff or 0x810702142201ffff

Severity

Info

Serviceable

786

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands

Lenovo x3650 M4 BD 5466, Installation And Service Manual

Search results

Summary of Contents for x3650 M4 BD 5466

Reviews:

Related manuals for x3650 M4 BD 5466

Brands by name

Popular brands