manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

0

0

0

0

0

0

0

0000

0000

0000

0000

0000

0000

0000

0000

0000

0000

000

000

000

000000

000000

000000

0

0000

0000

000

000

000

000000

000000

000000

0

0000

0000

PCI riser-card
assembly 2

PCI riser-card
assembly 1

Air baffle

Figure 154. Air baffle removal

To remove the air baffle, complete the following steps:

Step 1.

Read the safety information that begins on page “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables
(see “Turning off the server” on page 23).

Step 3.

Remove the cover (see “Removing the cover” on page 240).

Step 4.

Remove PCI riser-card assemblies, if needed (see “Removing a PCI riser-card assembly” on
page 37).

Step 5.

Place your fingers under the front and back of the top of the air baffle; then, lift the air baffle
out of the server.

Attention:

For proper cooling and airflow, replace the air baffle before you turn on the server.

Operating the server with the air baffle removed might damage server components.

Replacing the air baffle

Use this information to replace the air baffle.

To replace the air baffle, complete the following steps:

242

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

IBM B50 Service Manual preview
B50
Brand: IBM Pages: 198
IBM LS42 - BladeCenter - 7902 Service Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 194
IBM eServer 380 xSeries User Reference Manual preview
eServer 380 xSeries
Brand: IBM Pages: 112
Axis 570 MIO Quick Installation Manual preview
570 MIO
Brand: Axis Pages: 10
Gigabyte R283-S93-AAF1 User Manual preview
R283-S93-AAF1
Brand: Gigabyte Pages: 115
Leightronix UltraNEXUS-HD Flex Product Quick Manual preview
UltraNEXUS-HD Flex
Brand: Leightronix Pages: 5
TAPKO SIMip Operating Instructions preview
SIMip
Brand: TAPKO Pages: 2
Black Box PCA35A-R3 User Manual preview
PCA35A-R3
Brand: Black Box Pages: 30
IBM eServer BladeCenter HS20Type 8832 Problem Determination And Service Manual preview
eServer BladeCenter HS20Type 8832
Brand: IBM Pages: 112
Xerox FreeFlow Brochure preview
FreeFlow
Brand: Xerox Pages: 2
Sony XDAAI1PK Brochure preview
XDAAI1PK
Brand: Sony Pages: 8
Sony BSV-M1 - StorStation NAS Server Operating Instructions Manual preview
BSV-M1 - StorStation NAS Server
Brand: Sony Pages: 58
Supermicro AS-1010S-MR User Manual preview
AS-1010S-MR
Brand: Supermicro Pages: 96
Supermicro A+ User Manual preview
A+
Brand: Supermicro Pages: 130
Supermicro 8014T-T User Manual preview
8014T-T
Brand: Supermicro Pages: 124
XtendLan DVR-471 User Manual preview
DVR-471
Brand: XtendLan Pages: 27
Viavi G4-ObserverONE Manual preview
G4-ObserverONE
Brand: Viavi Pages: 11
Kystar Kommander-Z4 User Manual preview
Kommander-Z4
Brand: Kystar Pages: 46

Brands by name

Popular brands

Load more brands