Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 994

Page: 994 / 1022

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Clear the error log.

4. Run the test again.

5. Make sure that the drive firmware is at the latest level.

6. Rerun the test after upgrading to the latest firmware level.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-902-000 : Tape Test Failed

Tape Test Failed. Media is not detected.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Make sure that the drive firmware is at the latest level.

4. Rerun the test after upgrading to the latest firmware level.

5. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-903-000 : Tape Test Failed

980

Lenovo NeXtScale nx360 M5 Installation and Service Guide

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NeXtScale nx360 M5

Reviews:

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 994 / 1022

Search results

Summary of Contents for NeXtScale nx360 M5

Reviews: