Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 972

Page: 972 / 1022

NVIDIA User Diagnostic Test Failed.

Recoverable

Severity

Event

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Verify that the GPU is seated in the PCIe slot correctly by reseating the GPU. Then power cycle

the system.

2. Verify that the power connectors to the GPU are connected firmly. Then power cycle the system.

3. Run nvidia-smi -q In some cases this will report a poorly connected power cable.

4. Rerun the diagnostics, using the same GPU, on system that is known to be working. A variety of

system issues can cause diagnostic failure.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

409-903-000 : Nvidia::DiagnosticServiceProvider::Bandwidth Test Failed

Nvidia GPU Bandwidth Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Verify that the GPU is seated in the PCIe slot correctly by reseating the GPU. Then power cycle

the system.

2. Verify that the power connectors to the GPU are connected firmly. Then power cycle the system.

3. Run nvidia-smi -q In some cases this will report a poorly connected power cable.

4. Rerun the diagnostics, using the same GPU, on system that is known to be working. A variety of

system issues can cause diagnostic failure.

5. If the problem remains, contact your IBM technical-support representative.

958

Lenovo NeXtScale nx360 M5 Installation and Service Guide

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NeXtScale nx360 M5

Reviews:

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 972 / 1022

Search results

Summary of Contents for NeXtScale nx360 M5

Reviews: