manualshive.com logo in svg

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 210 / 1022

Share
Download
Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 210

Step 3.

Install the SAS/SATA adapter to the riser cage and close the retention bracket. It will secure the
SAS/SATA adapter in place when the adapter is firmly seated into the connector.

3

RAID adapter

Riser card assembly

Figure 133. RAID adapter installation

Step 4.

Route the backplane signal cables (see “Cabling hard disk drive with ServeRAID SAS/SATA
controller” on page 218).

Step 5.

Connect the signal cables to the SAS/SATA adapter:

Step 6.

Align the riser card golden finger with the planar RAID PCI slot.

Step 7.

Insert the adapter riser cage into the RAID connector until it is firmly seated.

Attention:

Incomplete insertion might cause damage to the server or the adapter.

Figure 134. ServeRAID adapter installation

Note:

Remove the PCI bracket that comes with ServeRAID N2215 adapter before installing it in

the dedicated connector on the system board.

Step 8.

Reconnect any cables that you removed.

196

Lenovo NeXtScale nx360 M5 Installation and Service Guide

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments