Lenovo NeXtScale nx360 M5 Installation And Service Manual Download Page 853

Page: 853 / 1022

•

405-907-000 : BRCM:TestLEDs Test Failed

A failure was detected while verifying operation of the status LEDs.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Brocade test results

The following messages can result when you run the Brocade test.

Test results for the DSA Brocade test

The following messages can result when you run the DSA Brocade test.

•

218-000-000 : Brocade:MemoryTest Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Appendix C. DSA diagnostic test results

839

Summary of Contents for NeXtScale nx360 M5































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NeXtScale nx360 M5

Reviews:

Lenovo NeXtScale nx360 M5, Installation And Service Manual, Page: 853 / 1022

Search results

Summary of Contents for NeXtScale nx360 M5

Reviews: