manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 98 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 98

Set the outgoing fax resolution

The outgoing fax resolution setting determines the maximum resolution supported by the receiving

fax. The fax accessory uses the highest possible resolution (as limited by this setting) and the

maximum resolution of the receiving fax.

NOTE:

Faxes wider than 21.25 cm (8.5 inches) are automatically sent by using standard or fine

resolution, to reduce phone time.

NOTE:

The default resolution setting is a lower dpi than previous product model default resolution

settings. For example, previous product models had a default resolution of FINE (200 x 200 dpi).

NOTE:

The higher the resolution, the longer the transmission time required.

NOTE:

LAN fax settings resolution settings vary by vendor and may differ from the settings listed

below.

1.

From the Home screen, scroll to and touch the 

Administration

 button.

2.

Open the following menus:

●

Fax Settings

●

Fax Send Settings

●

Default Job Options

●

Resolution

3.

Touch one of the following resolution settings:

●

Standard (100 x 200dpi)

 (default)

●

Fine (200 x 200dpi)

●

Superfine (300 x 300dpi)

4.

Touch the 

Save

 button.

Original sides

1.

From the Home screen, scroll to and touch the 

Administration

 icon.

2.

Open the following menus:

●

Fax Settings

●

Fax Send Settings

●

Default Job Options

●

Original Sides

3.

Touch one of the following options:

●

1-sided

 (default)

●

2-sided

86 Chapter 3   HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments