manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 140 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 140

Troubleshooting

 menu settings

T.30 Trace: The T.30 trace is a printed report which

produces a record of all the communications between the

sending and receiving fax machines for the last Fax

transmission or reception. The report has many technical

details which are usually beyond the scope of most users.

However the report contains detailed error codes and other

information that might be useful in troubleshooting a

particular problem related to sending or receiving a FAX. The

report contents might be requested by an HP service

representative when trying to determine the cause of a

problem and will help to determine the appropriate action.

 

V34

: This setting has two values (Normal and Off) that

control the modem's baud rate. The Normal setting allows

the modem to select (negotiate with the other modem) any of

the supported baud rates up to 33,600 bps. The Off setting

sets the maximum baud rate to 14,400 bps. This setting

remains set, until changed.

 

Speaker Mode

: This service setting has two modes, Normal

and Diagnostic. In Normal mode, the modem speaker is

turned on during dialing through the initial connection and

then shuts off. For Diagnostic mode, the speaker is turned on

and remains on for all fax communications until the setting is

returned to Normal.

Settings in the Resets menu

Open the 

Administration

 menu, and then select the 

Resets

 menu.

Resets

 menu settings

Restore Factory Telecom Settings

 or 

Restore Default

Telecom Settings

: This selection resets several menu

changes back to their default settings. This includes the

maximum baud rate, ring-burst off time, V.34, speaker mode,

and transmit signal loss.

Firmware upgrades

The firmware on the fax accessory can be updated. Fax firmware updates occur as part of an overall

product firmware update. See the product user guide for more information.

128 Chapter 3   HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments