HP CC487-91209 Fax Manual Download Page 156

Page: 156 / 168

Canadian DOC regulations

Complies with Canadian EMC Class A requirements.

« Conforme à la classe A des normes canadiennes de compatibilité électromagnétiques. « CEM ». »

Industry Canada CS-03 requirements

Notice: The Industry Canada label identifies certified equipment. This certification means the

equipment meets certain telecommunications network protective, operational, and safety

requirements as prescribed in the appropriate Terminal Equipment Technical Requirement

document(s). The Department does not guarantee the equipment will operate to the user’s

satisfaction. Before installing this equipment, users should ensure that it is permissible for the

equipment to be connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. The customer should be aware that

compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier.

Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users

should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines, and internal metallic water pipe system, if present, are connected together. This

precaution can be particularly important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalence

Number (REN) of this device is 0.0.

Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an

indication of the maximum number of terminals allowed to be connected to a telephone interface. The

termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the Ringer Equivalence Number of all the devices does not exceed five (5.0). The

standard connecting arrangement code (telephone jack type) for equipment with direct connections to

the telephone network is CA11A.

144 Appendix C Regulatory information

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 156 / 168

Search results

Summary of Contents for CC487-91209

Reviews: