manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 66 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 66

Fax Send

 settings

Maximum baud rate

: This setting provides a list of baud rates

to select for operation. If the fax is having communication

errors, use this setting to select slower baud rates to

determine if the communication error is caused by the phone

line. First drop down to 14,400 bps, and then to 9,600 bps.

Once this setting is set, it remains set until changed.

 

TCF T.30 Delay Timer

: This setting has a range between 60

to 255 ms. It should be left to its default value of 60 ms. Use

this setting when directed by an HP technical support agent

as adjustment procedures associated with it is beyond the

scope of this guide.

 

TCF Extend

: This setting has a range between 0 to 2550 ms.

It should be left to its default value of 0 ms. Use this setting

when directed by an HP technical support agent as

adjustment procedures associated with it is beyond the

scope of this guide.

Fax Receive

 settings

Ring Interval

: This setting is used to adjust for some PBX

ring signals. Use this setting when directed by an

HP technical support agent.

 

Ring Frequency

: This setting has a range between 1 to 200

Hz. It should be left at its default value of 68 Hz. Use this

setting when directed by an HP technical support agent as

adjustment procedures associated with it is beyond the

scope of this guide.

Settings in the Troubleshooting menu

Open the 

Administration

 menu, and then select the 

Troubleshooting

 menu.

Troubleshooting

 menu settings

Fax T.30 Trace: The Fax T.30 trace is a printed report which

produces a record of all the communications between the

sending and receiving fax machines for the last Fax

transmission or reception. The report has many technical

details which are usually beyond the scope of most users.

However the report contains detailed error codes and other

information that might be useful in troubleshooting a

particular problem related to sending or receiving a FAX. The

report contents might be requested by an HP service

representative when trying to determine the cause of a

problem and will help to determine the appropriate action.

(For error code information, see 

Fax error messages

on page 47

.)

 

Fax V.34

: This setting has two values (Normal and Off) that

control the modem's baud rate. The Normal setting allows

the modem to select (negotiate with the other modem) any of

the supported baud rates up to 33,600 bps. The Off setting

sets the baud rate to a maximum of 14,400 bps. This setting

remains set, until changed.

 

Fax Speaker mode

: This service setting has two modes,

Normal and Diagnostic. In Normal mode, the modem

speaker is turned on during dialing through the initial

connection and then shuts off. For Diagnostic mode, the

speaker is turned on and remains on for all fax

communications until the setting is returned to Normal.

54 Chapter 2   HP Color LaserJet CM3530 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments