manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 53 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 53

T.30 Report

Voice Calls do not cause a T.30 report to print. All retry attempts cause a T.30 report to print. For

more information, see 

Service settings on page 53

.

Secure settings

Two settings, fax forwarding and fax printing, are secure features and require a PIN. The first time

you access either setting, you will be required to create a PIN. After you create that PIN, it is used to

access both features. That is, if a PIN that has been created for fax forwarding it is also used to

access fax printing, or if the PIN was first created for fax printing, it must be used to access fax

forwarding. Only one PIN can be created to access these secure settings.

If fax call report is enabled with thumbnails, a report prints with a thumbnail of the first page of the fax

when fax printing or fax forwarding is enabled. If you want secure fax printing, disable printing the

thumbnail on the fax call report.

Change your PIN

This procedure describes how to change your existing PIN.

CAUTION:

Always save your PIN in a secure place. If you lose your PIN, you must contact

HP Service Support for information about how to reset the PIN. For more information, see 

Customer

support on page 131

.

1.

On the control panel, scroll to and touch the 

Administration

 icon to open the Administration

menu.

2.

Touch 

Default Job Options

 to display the Default Job Options menu.

3.

Touch 

Default Fax Options

 to display the Default Fax Options menu.

4.

Touch 

Fax Receive

 to display the Fax Receive screen.

5.

Touch 

Fax Forwarding

 to display the PIN screen.

6.

Using the keypad, type the PIN (at least four digits), and then touch 

OK

 to display the Fax

Forwarding screen.

7.

Touch 

Change PIN

 to display the PIN screen.

8.

Using the keypad, type the new PIN (at least four digits), and then touch 

OK

.

9.

Using the keypad, confirm the new PIN, and then touch 

OK

.

10.

Touch 

OK

 again.

Use Fax over VoIP networks

VoIP technology converts the analog phone signal into digital bits. These are then assembled into

packets which travel on the Internet. The packets are converted and transmitted back to analog

signals at or near the destination.

The transmission of the information on the Internet is done digitally instead of analog. Therefore,

there are different constraints on the fax transmission that may require different fax settings than the

analog Public Switched Telephone Network (PSTN). Fax is very dependent upon timing and signal

quality, so a fax transmission is more sensitive to a VoIP environment.

ENWW

Use fax 41

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments