HP CC487-91209 Fax Manual Download Page 158

Page: 158 / 168

New Zealand Telecom Statements

The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has

accepted that the item complies with minimum conditions for connection to its network. It indicates no

endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it

provides no assurance that any item will work correctly in all respects with another item of

Telepermitted equipment of a different make or model, nor does it imply that any product is

compatible with all of Telecom’s network services.

This equipment may not provide for the effective hand-over of a call to another device connected to

the same line.

This equipment shall not be set up to make automatic calls to the Telecom “111” Emergency Service.

This product has not been tested to ensure compatibility with the FaxAbility distinctive ring service for

New Zealand.

146 Appendix C Regulatory information

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 158 / 168

Search results

Summary of Contents for CC487-91209

Reviews: