manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 55 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 55

Solve fax problems

Check fax accessory status

If the analog-fax accessory does not appear to be functioning, print a Fax Accessory Page to check

the status.

1.

On the control panel, scroll to and touch the 

Administration

 icon to open the Administration

menu.

2.

Scroll to and touch 

Information

.

3.

Scroll to and touch 

Configuration/Status Pages

.

4.

Scroll to and touch 

Configuration page

 to print the configuration pages.

On the Fax Accessory Page of the Information Page, under the HARDWARE INFORMATION

heading, check the MODEM STATUS. The following table identifies the status conditions and

possible solutions.

OPERATIONAL / ENABLED

1

The analog-fax accessory is installed and ready.

OPERATIONAL / DISABLED

1

The fax accessory is installed and operational, however,

HP Digital Sending utility has either disabled the product fax

feature or has enabled LAN fax. When LAN fax is enabled,

the analog-fax feature is disabled. Only one fax feature,

either LAN fax or analog fax, can be enabled at a time.

NON-OPERATIONAL / ENABLED/DISABLED

1

A firmware failure has been identified. The firmware should

be updated, see 

Firmware upgrades on page 55

.

DAMAGED / ENABLED/DISABLED

1

Fax accessory has failed; reseat the fax accessory card and

check for bent pins. If the status is still DAMAGED, replace

the analog-fax accessory card.

1

ENABLED indicates that the analog fax accessory is enabled, turned on; DISABLED indicates that LAN fax is enabled

(analog fax is turned off).

Fax feature is not operating

The fax accessory is installed but the icon does not appear on the product main screen.

Cause

Solution

HP MFP Digital Sending Software Configuration utility has

disabled the analog-fax feature.

Use the HP MFP Digital Sending Software Configuration

utility to enable the analog-fax feature.

The accessory is not operating correctly.

Check the fax accessory status. If the status is

NON-OPERATIONAL, new firmware might need to be

installed.

If the status is DAMAGED and you just installed the card, try

reseating the card and check for bent pins.

If the status is DAMAGED and the card is installed correctly,

the card might need to be replaced.

Faulty formatter board.

Contact your HP service representative for service.

ENWW

Solve fax problems 43

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments