manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 70 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 70

Install the fax accessory

The following sections describe the installation procedure for each of the following printers:

●

Install the fax accessory in the HP Color LaserJet CM4540

●

Install the fax accessory in the HP Color LaserJet M4555 MFP Series

●

Install the fax accessory in the HP LaserJet Enterprise 500 MFP Series

●

Install the fax accessory in the HP LaserJet Enterprise 500 Color MFP Series

●

Install the fax accessory in the HP LaserJet Enterprise M725 MFP Series

Install the fax accessory in the HP Color LaserJet CM4540

1.

Turn the product off.

2.

Disconnect all power and interface cables.

NOTE:

This illustration might not show all the cables.

58 Chapter 3   HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments