HP CC487-91209 Fax Manual Download Page 76

Page: 76 / 168

Locate the fax-accessory connector opening on the formatter. Align the connector on the fax-

accessory with the opening on the formatter. The top edge of the fax-accessory will fit into the

slot on the metal frame of the formatter when properly positioned (callout 1). Align the connector

on the fax-accessory to the connector on the formatter and push down firmly (callout 2).

Align the formatter board in the tracks at the bottom of the slot, and then slide the board back

into the product. Tighten the thumb screws.

Reconnect the power cable and interface cables, and turn the product on.

64 Chapter 3 HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 76 / 168

Search results

Summary of Contents for CC487-91209

Reviews: